Siemens 240v vfd manual

9000X AF Drives 9000X AF Drives MN04001004E—May 2011 eaton.com i Disclaimer of Warranties and Limitation of Liability The information, recommendations, descriptions, and safety notations in this document are Siemens Energy & Automation ABSTRACT Variable Frequency drives (VFD's) have been available to the cement industry for a number of years. However, with improvements to VFD's (power quality, reliability, stability, costs), their increased acceptance and with the emphasis to cut production costs, VFD usage has become more widespread. Highlights Easy-to-install Easy-to-use Easy to save money n Push-through and wall mounting — side-by-side is possible n USS and Modbus RTU at terminals n Integrated braking chopper for 7.5 kW to 30 kW (10 hp up to 40 hp) n Electromagnetic compatibility (EMC) category C1 / C2 n Parameter loading without power supply n Easy commissioning with mobile device or laptop with web server With the compact SINAMICS V20 converter, Siemens offers a simple and economical drive solution for applications with simple motion sequences and basic requirements. SINAMICS V20 sets itself apart with its quick commissioning times, ease of operation, robustness and cost-efficiency. Practical application examples and descriptions are available At SIEMENS VFD.us (Specialized Electronic Services), we are Authorized SIEMENS Simovert 6SE Distributors and a Certified SIEMENS repair center located in the United States. SIEMENS 6SE6420-2AB11-2AA1 MICROMASTER 420 WITH BUILT IN CLASS A FILTER 1AC 200-240V 10/-10% 47-63HZ CONSTANT TORQUE POWER 0.12 KW OVERLOAD 150% FOR 60S VARIABLE TORQUE Power Module PM240-2 Hardware Installation Manual Updated from 01/2019 to 01/202 0 01/2020 A5E33294624B AL Preface Fundamental safety instructions 1 2 Installing 3 Connecting 4 Service and maintenance 5 Technical data 6 Spare parts 7 Accessories 8 Appendix A Siemens AG Digital Industries Postfach 48 48 90026 NÜRNBERG Drive / VFD. A drive is needed to turn control the motor at variable speeds. Determine the correct drive family select by using the Drive Selection Guide flowchart. We do not have a requirement for communication, but our drive is over 20HP, so the selection guide suggests we use the G120 family. Series: G120. SIEMENS V20 380-480 V 3AC -15%/+10% 47-6 Rated power 22 kW with 150% overload for 60 sec. small output overload: 30 kW with 110% overload for 60 sec. unfiltered I/O interface: 4 DI, 2 DQ, 2 AI, 1 AO Fieldbus: USS/Modbus RTU with built-in BOP Degree of protection IP20/UL. Additional Information: Delivery Time: 1-4 WEEKS. Application Note AP0400076EN VFD Wiring Best Practices Effective July 2014 2 EATON CORPORATION eaton.com Control Wiring Similar consideration need to be taken when looking at the control wiring. Sizing - The sizing of the control wire is again going to be based off the current load and voltage that will be on them but it is suggested that it is rated for 600V. Siemens VFD troubleshooting starts with checking the electric motor and VFD terminal connections. Motor and VFD connections can be overlooked, loose, or, wired to the incorrect terminals; so, checking all connections is suggestedbefore pulling the VFD and sending it in for a repair evaluation. Heat cycles and mechanical vibration can lead to 7. Press and hold the OK button for 2 seconds to save settings. The VFD will now attempt to change the motor data. If the VFD faults at this time, then the data is not valid. Double check the motor data to ensure i